Homemade Lathe & Disc Sander Part2YouTube↗  IA↗(long shot)
Science & Technology  649.6K views 7.4K likes 139 dislikes   03 Nov 2016
Paoson Woodworking 630K subscribers Spain YouTube↗


Please select the problem
You must specify your email and describe the problem in detail
Describe your problem in detail if it's not obvious

Contributed subtitles
Russian Daniyar Nurgaliyev
German Reinhold Poier
Italian Paolo
Dutch cchaos11
Portuguese (Brazil) A Cosmic Castaway
Chinese (Taiwan) haomin鄭
Click to Play Video Click to Play Video
hola de nuevo!
hello again I will begin the second
comenzaré este segundo vídeo fabricando el contrapunto y el soporte de herramientas
video by making the tailstock and tool
que aquí podéis ver dibujado en 3D.
rest which you can see in this 3d model
Primero cortaré y pegaré estas dos piezas para el contrapunto.
first I'll cut and glue these pieces for
Igual que anteriormente, usaré un par de tornillos además de la cola.
the tailstock just like before I'll use a pair of screws in addition to glue now
Lijo todos los cantos,
I sand the edges
la tercera pieza está solo atornillada, para poder volver a retirar má adelante.
the third piece will only be screwed in so that it can be removed later I
Mecanizo su base, y la atornillo a las tres piezas.
machined the vase and screw it to the three pieces you
Marcaré el centro para agujerear con la propia varilla roscada
I'll mark the center to drill a hole with a threaded rod itself it seems to
parece coincide bastante bien con la plantilla!
match the template quite well
La agujereo e inserto esta tuerca larga a presión.
I drill a hole in it and press fit this coupling nut
Ahora agujereo la tercera pieza con una broca del diámetro de la varilla roscada.
now I make a hole in the third piece using a bit with the same diameter as the threaded rod at this point I can
En este momento ya puedo encolar las tres piezas.
glue the three pieces
Mecanizo y atornillo estos refuerzos.
I'm machine and screw in these reinforcements you
Introduzco su asa, que he agujereado con una broca de 1mm menos que la varilla roscada.
I attached the handle which I drove with a bit with one millimeter less diameter than the threaded rod now I machined the
Ahora mecanizaré las piezas del portaherramientas, las encolo de la misma forma que antes.
pieces for the tool rest and glued them together like before
Con la 3D Router mecanizo este canal de ajuste.
with a 3d router I machine this fitting grow you
Realizo un agujero aquí para introducir un trozo de varilla roscada, que me permitirá regular en altura
I make a hole here to insert a piece of threaded rod that will allow me to
el portaherrramientas.
adjust the height of the tool work the
La broca debe tener de 1mm menos que la varilla para que entre roscado.
bed must be one millimeter less than the rod so that it will fit in
Aquí agujereo con una broca del diámetro exacto a la varilla.
here I make holes with a bit of the same diameter as the rod
Después de mecanizar todas las piezas del portaherramientas, corto y pego con cola de contacto
after machining all the to rest pieces I cut and glue these pieces of B 120
estos trozos de lija P120 en la base,
sandpaper with contact adhesive this
esto ayudará a fijar los dos accesorios en el lugar deseado.
will help us love the two accessories at the desired position
He preparado todos los pomos,
I've prepared all the knobs you can see
podéis ver como hacerlos en este otro vídeo.
how to make them in this other video
También he instalado los interruptores y la emergencia,
I've also installed the switches and an
he usado este modelo que tenía por el taller, pero si tenéis que comprarlo, recomiendo
emergency lock I use this model I had in my workshop but if you have to buy one I
usar uno de este tipo,
recommend using one of this type it's
es más barato, fácil de instalar y es mas compacto.
cheaper easier to install and more compact
Ahora posicionaré el motor en su lugar, usaré estas bisagras para realizar el giro.
now I put the motor in place I will use these hinges to make a turn
Usaré otra tuerca larga para fabricar la punta de tracción.
I'll use another coupling nut to make the drive center I mark it like this and
Marco de esta forma y cortaré con una sierra para metales.
cut it with a hacksaw
Ahora realizaré un biser con la radia para afilar las puntas.
now make a bevel with the angle grinder to sharpen the tips
Termino con una lima y una dremel.
I finished the job with a file and a dremel
Agujereo y avellano este trozo de aluminio, para proteger la cabeza de portaherramientas.
I drill and countersink this piece of aluminium to protect the tool rest
Y por fin realizaré una pequeña prueba con este trozo de fresno.
and finally I'll do a little test with a piece of ash wood after marking the
Después de marcar los centros, lo posiciono en su lugar, aprieto todos los pomos y regulo en altura el portaherramientas.
Centers I put it in place tighten all the knobs and adjust the two rests height
Al tratarse de un trozo de poco diámetro, voy a seleccinar la combinación de poleas con más revoluciones.
since it's not a white piece I'll select the pulley combination with the most revolutions per minute
Parece que todo va bien!
seems everything is working as it should
Va suave, sin vibraciones y la punta de tacción no patina.
it runs smoothly without vibrations and the drive center isn't slipping off
Alguno de vosotros me ha preguntado por el motor...
some of you have asked me about the
se trata de un motor monofase de 1HP y 1500 rpm.
motor it's a single stage 1 HP motor with 1500 revolutions per minute using
Con esta configuración de poleas consigo tres velocidades, una de 800rpm para piezas de mayor diámetro,
this bully configuration I obtain 3 speeds 800 revolutions per minute the pieces with a wider diameter 1500
otra de 1500 rpm y la más rápida, de 2800 rpm, que ahora estoy usando.
revolutions per minute and the fastest 2,800 revolutions per minute which I'm
Están dentro del rango que se suele utilizar para tornear madera.
using here it's within the usual range of speeds from waving wood
Esto es todo por hoy,
that's all for today in the next video
en el siguiente vídeo prepararé el disco de lijado,
I'll prepare the disk sander see you
hasta pronto!
soon you
Similar videos:

Homemade Lathe & Disc Sander Part1
Paoson Woodworking
683.8K views 7.3K likes 128 dislikes 28 Oct 201667% match


Homemade Lathe & Disc Sander Part3
Paoson Woodworking
634K views 7.5K likes 140 dislikes 11 Nov 201667% match

How to Make a Grinding Wheel for the Lathe
Paoson Woodworking
850.5K views 8.2K likes 271 dislikes 05 Apr 201733% match

Lathe Sanding Station: Thickness Sander Part1
Paoson Woodworking
322.3K views 3.3K likes 101 dislikes 10 Feb 201732% match

How to make a Folding Knife
Paoson Woodworking
2.7M views 25.3K likes 1.5K dislikes 09 Mar 201732% match

Homemade Angle Drill Press Vise
Paoson Woodworking
570.3K views 6.1K likes 132 dislikes 13 Sep 201630% match

Lathe Sanding Station: Thickness Sander Part2
Paoson Woodworking
990.5K views 7.7K likes 311 dislikes 17 Feb 201729% match

Making a Mini Axe (free plans)
Paoson Woodworking
889.2K views 8.9K likes 486 dislikes 03 May 201727% match

How to make a plywood Tatami Bed
Paoson Woodworking
2.3M views 19.7K likes 773 dislikes 22 Mar 201727% match

Serra de bancada invertida #01(parte_01) - inclinação 45º com arduino
A Minha Bancada
451.1K views 7.8K likes 244 dislikes 05 May 201927% match

How to Make a Faceplate & Adjustable Chuck
Paoson Woodworking
677.2K views 4.1K likes 278 dislikes 02 Dec 201627% match

There's a trick for making all the drawers in this small-parts storage cabinet. .
Steve Ramsey - Woodworking for Mere Mortals
865.4K views 8K likes 284 dislikes 19 Sep 201427% match

Cheap and easy-to-make Open Wardrobe
Paoson Woodworking
28.9K views 1K likes 27 dislikes 26 Jul 201926% match

DIY | Como Fazer uma Caixa para Presente - Gift Box
Pink&Fun
453.9K views 10.9K likes 190 dislikes 09 Jan 201626% match

Easy-to-make Belt Sander/Grinder Wheels
Paoson Woodworking
494.7K views 4K likes 251 dislikes 10 Oct 201726% match

How to build a router table for Woodworking for under $10 - Woodworking video for beginners
Warren Downes - One Wood
457.6K views 4.1K likes 146 dislikes 24 Sep 201425% match

How To Build A Wood Shed
Frank Does It
892.7K views 21.5K likes -1 dislikes 19 Mar 201925% match








Settings Privacy About Contact Donate